move input club keyboards into vendor folder (#15788)

keyboards/input_club/ergodox_infinity/readme.md

@@ -5,19 +5,19 @@ for the left and right halves seperately.  To flash them:
 
   - Make sure you are in the top-level qmk_firmware directory
 
-  - Build the firmware with `make ergodox_infinity:keymapname`
+  - Build the firmware with `make input_club/ergodox_infinity:keymapname`
 
   - Plug in the left hand keyboard only.
 
   - Press the program button (back of keyboard, above thumb pad).
 
-  - Install the firmware with `sudo make ergodox_infinity:keymapname:dfu-util`
+  - Install the firmware with `sudo make input_club/ergodox_infinity:keymapname:dfu-util`
 
   - Plug in the right hand keyboard only.
 
   - Press the program button (back of keyboard, above thumb pad).
 
-  - Install the firmware with `sudo make ergodox_infinity:keymapname:dfu-util`
+  - Install the firmware with `sudo make input_club/ergodox_infinity:keymapname:dfu-util`
 
 More information on the Infinity firmware is available in the [TMK/chibios for
 Input Club Infinity Ergodox](https://github.com/fredizzimo/infinity_ergodox/blob/master/README.md)
@@ -43,7 +43,7 @@ They only need to be done once, unless you reset the EEPROM later.
 
   - Plug in the left keyboard half to the computer, and press its program button.
 
-  - Flash the left half with `make ergodox_infinity:default:dfu-util-split-left`
+  - Flash the left half with `make input_club/ergodox_infinity:default:dfu-util-split-left`
     (If you need to use a different method to flash your keyboard, still run this command,
     and abort it with Ctrl+C when the flashing attempts starts to print errors,
     then flash the built firmware).
@@ -53,13 +53,13 @@ They only need to be done once, unless you reset the EEPROM later.
 
   - Plug in the right keyboard half to the computer, and press its program button.
 
-  - Flash the right half with `make ergodox_infinity:default:dfu-util-split-right`
+  - Flash the right half with `make input_club/ergodox_infinity:default:dfu-util-split-right`
 
   - On the right half, press the top vertical 1.5U key (second from the top in the leftmost column) once,
     then the 1U key at the bottom in the opposite corner (bottom right corner).
 
   - Add `#define EE_HANDS` to the config.h file of your keymap, and build your firmware using
-    `make ergodox_infinity:keymapname`.
+    `make input_club/ergodox_infinity:keymapname`.
 
   - After this, you can flash both halves with the same firmware, _without_ risking a mirrored keyboard when connected the wrong way.
     If you reset your EEPROM later, you'll have to follow these steps again, though.

keyboards/input_club/infinity60/readme.md

@@ -8,10 +8,10 @@ A compact community driven keyboard.
 
 Make example for this keyboard (after setting up your build environment):
 
-    make infinity60:default
+    make input_club/infinity60/rev1:default
 
 Flashing example for this keyboard:
 
-    make infinity60:default:flash
+    make input_club/infinity60/rev1:default:flash
 
 See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs).

keyboards/input_club/infinity60/rules.mk

@@ -26,7 +26,7 @@ BACKLIGHT_ENABLE = no       # Enable keyboard backlight functionality
 RGBLIGHT_ENABLE = no        # Enable keyboard RGB underglow
 AUDIO_ENABLE = no           # Audio output
 
-DEFAULT_FOLDER = infinity60/led
+DEFAULT_FOLDER = input_club/infinity60/led
 
 LAYOUTS = 60_ansi_split_bs_rshift
 

keyboards/input_club/k_type/readme.md

@@ -8,10 +8,10 @@ Firmware for custom keyboard PCB with TKL Key Layout
 
 Make example for this keyboard (after setting up your build environment):
 
-    make k_type:default
+    make input_club/k_type:default
 
 Flashing example for this keyboard:
 
-    make k_type:default:flash
+    make input_club/k_type:default:flash
 
 See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs).