diff --git a/docs/features/joystick.md b/docs/features/joystick.md
index 69db4655d5..cbf6c6daf7 100644
--- a/docs/features/joystick.md
+++ b/docs/features/joystick.md
@@ -1,6 +1,6 @@
 # Joystick {#joystick}
 
-This feature provides game controller input as a joystick device supporting up to 6 axes and 32 buttons. Axes can be read either from an [ADC-capable input pin](../drivers/adc), or can be virtual, so that its value is provided by your code.
+This feature provides game controller input as a joystick device supporting up to 6 axes, 32 buttons and a hat switch. Axes can be read either from an [ADC-capable input pin](../drivers/adc), or can be virtual, so that its value is provided by your code.
 
 An analog device such as a [potentiometer](https://en.wikipedia.org/wiki/Potentiometer) found on an analog joystick's axes is based on a voltage divider, where adjusting the movable wiper controls the output voltage which can then be read by the microcontroller's ADC.
 
@@ -37,6 +37,42 @@ By default, two axes and eight buttons are defined, with a reported resolution o
 You must define at least one button or axis. Also note that the maximum ADC resolution of the supported AVR MCUs is 10-bit, and 12-bit for most STM32 MCUs.
 :::
 
+### Hat Switch {#hat-switch}
+
+To enable the 8-way hat switch, add the following to your `config.h`:
+
+```c
+#define JOYSTICK_HAS_HAT
+````
+
+The position can be set by calling `joystick_set_hat(value)`. The range of values moves clockwise from the top (ie. north), with the default "center" position represented by a value of `-1`:
+
+```
+         0
+ 7       N       1
+   NW .--'--. NE
+     /       \
+6 W |   -1    | E 2
+     \       /
+   SW '--.--' SE
+ 5       S       3
+         4
+```
+
+Alternatively you can use these predefined names:
+
+|Define                  |Value|Angle|
+|------------------------|-----|-----|
+|`JOYSTICK_HAT_CENTER`   |`-1` |     |
+|`JOYSTICK_HAT_NORTH`    |`0`  |0°   |
+|`JOYSTICK_HAT_NORTHEAST`|`1`  |45°  |
+|`JOYSTICK_HAT_EAST`     |`2`  |90°  |
+|`JOYSTICK_HAT_SOUTHEAST`|`3`  |135° |
+|`JOYSTICK_HAT_SOUTH`    |`4`  |180° |
+|`JOYSTICK_HAT_SOUTHWEST`|`5`  |225° |
+|`JOYSTICK_HAT_WEST`     |`6`  |270° |
+|`JOYSTICK_HAT_NORTHWEST`|`7`  |315° |
+
 ### Axes {#axes}
 
 When defining axes for your joystick, you must provide a definition array typically in your `keymap.c`.
@@ -149,6 +185,8 @@ Contains the state of the joystick.
    A bit-packed array containing the joystick button states. The size is calculated as `(JOYSTICK_BUTTON_COUNT - 1) / 8 + 1`.
  - `int16_t axes[]`  
    An array of analog values for each defined axis.
+ - `int8_t hat`  
+   The hat switch position.
  - `bool dirty`  
    Whether the current state needs to be sent to the host.
 
@@ -222,3 +260,14 @@ Set the value of the given axis.
    The axis to set the value of.
  - `int16_t value`  
    The value to set.
+
+---
+
+### `void joystick_set_hat(int8_t value)` {#api-joystick-set-hat}
+
+Set the position of the hat switch.
+
+#### Arguments {#api-joystick-set-hat-arguments}
+
+ - `int8_t value`  
+   The hat switch position to set.
diff --git a/quantum/joystick.c b/quantum/joystick.c
index 32f19b2cd9..62893fd199 100644
--- a/quantum/joystick.c
+++ b/quantum/joystick.c
@@ -29,6 +29,9 @@ joystick_t joystick_state = {
             0
 #endif
         },
+#ifdef JOYSTICK_HAS_HAT
+    .hat = -1,
+#endif
     .dirty = false,
 };
 
@@ -145,6 +148,13 @@ void joystick_set_axis(uint8_t axis, int16_t value) {
     }
 }
 
+#ifdef JOYSTICK_HAS_HAT
+void joystick_set_hat(int8_t value) {
+    joystick_state.hat   = value;
+    joystick_state.dirty = true;
+}
+#endif
+
 void joystick_init(void) {
     joystick_init_axes();
 }
diff --git a/quantum/joystick.h b/quantum/joystick.h
index 5a69ceac64..24f80c1ad6 100644
--- a/quantum/joystick.h
+++ b/quantum/joystick.h
@@ -52,6 +52,16 @@
 
 #define JOYSTICK_MAX_VALUE ((1L << (JOYSTICK_AXIS_RESOLUTION - 1)) - 1)
 
+#define JOYSTICK_HAT_CENTER -1
+#define JOYSTICK_HAT_NORTH 0
+#define JOYSTICK_HAT_NORTHEAST 1
+#define JOYSTICK_HAT_EAST 2
+#define JOYSTICK_HAT_SOUTHEAST 3
+#define JOYSTICK_HAT_SOUTH 4
+#define JOYSTICK_HAT_SOUTHWEST 5
+#define JOYSTICK_HAT_WEST 6
+#define JOYSTICK_HAT_NORTHWEST 7
+
 // configure on input_pin of the joystick_axes array entry to NO_PIN
 // to prevent it from being read from the ADC. This allows outputting forged axis value.
 #define JOYSTICK_AXIS_VIRTUAL \
@@ -73,7 +83,10 @@ extern joystick_config_t joystick_axes[JOYSTICK_AXIS_COUNT];
 typedef struct {
     uint8_t buttons[(JOYSTICK_BUTTON_COUNT - 1) / 8 + 1];
     int16_t axes[JOYSTICK_AXIS_COUNT];
-    bool    dirty;
+#ifdef JOYSTICK_HAS_HAT
+    int8_t hat;
+#endif
+    bool dirty;
 } joystick_t;
 
 extern joystick_t joystick_state;
@@ -129,4 +142,11 @@ void joystick_read_axes(void);
  */
 void joystick_set_axis(uint8_t axis, int16_t value);
 
+/**
+ * \brief Set the position of the hat switch.
+ *
+ * \param value The hat switch position to set.
+ */
+void joystick_set_hat(int8_t value);
+
 /** \} */
diff --git a/tmk_core/protocol/host.c b/tmk_core/protocol/host.c
index 732fbdc37d..df805c827c 100644
--- a/tmk_core/protocol/host.c
+++ b/tmk_core/protocol/host.c
@@ -193,6 +193,10 @@ void host_joystick_send(joystick_t *joystick) {
             },
 #    endif
 
+#    ifdef JOYSTICK_HAS_HAT
+        .hat = joystick->hat,
+#    endif
+
 #    if JOYSTICK_BUTTON_COUNT > 0
         .buttons =
             {
diff --git a/tmk_core/protocol/report.h b/tmk_core/protocol/report.h
index 37c8ea48f1..d854f51d5c 100644
--- a/tmk_core/protocol/report.h
+++ b/tmk_core/protocol/report.h
@@ -246,6 +246,11 @@ typedef struct {
     joystick_axis_t axes[JOYSTICK_AXIS_COUNT];
 #endif
 
+#ifdef JOYSTICK_HAS_HAT
+    int8_t  hat : 4;
+    uint8_t reserved : 4;
+#endif
+
 #if JOYSTICK_BUTTON_COUNT > 0
     uint8_t buttons[(JOYSTICK_BUTTON_COUNT - 1) / 8 + 1];
 #endif
diff --git a/tmk_core/protocol/usb_descriptor.c b/tmk_core/protocol/usb_descriptor.c
index e7d12a07d9..c7fb660b65 100644
--- a/tmk_core/protocol/usb_descriptor.c
+++ b/tmk_core/protocol/usb_descriptor.c
@@ -247,6 +247,23 @@ const USB_Descriptor_HIDReport_Datatype_t PROGMEM SharedReport[] = {
             HID_RI_INPUT(8, HID_IOF_DATA | HID_IOF_VARIABLE | HID_IOF_ABSOLUTE),
 #    endif
 
+#    ifdef JOYSTICK_HAS_HAT
+            // Hat Switch (4 bits)
+            HID_RI_USAGE(8, 0x39), // Hat Switch
+            HID_RI_LOGICAL_MINIMUM(8, 0x00),
+            HID_RI_LOGICAL_MAXIMUM(8, 0x07),
+            HID_RI_PHYSICAL_MINIMUM(8, 0),
+            HID_RI_PHYSICAL_MAXIMUM(16, 315),
+            HID_RI_UNIT(8, 0x14),  // Degree, English Rotation
+            HID_RI_REPORT_COUNT(8, 1),
+            HID_RI_REPORT_SIZE(8, 4),
+            HID_RI_INPUT(8, HID_IOF_DATA | HID_IOF_VARIABLE | HID_IOF_ABSOLUTE | HID_IOF_NULLSTATE),
+            // Padding (4 bits)
+            HID_RI_REPORT_COUNT(8, 0x04),
+            HID_RI_REPORT_SIZE(8, 0x01),
+            HID_RI_INPUT(8, HID_IOF_CONSTANT),
+#    endif
+
 #    if JOYSTICK_BUTTON_COUNT > 0
             HID_RI_USAGE_PAGE(8, 0x09), // Button
             HID_RI_USAGE_MINIMUM(8, 0x01),
diff --git a/tmk_core/protocol/vusb/vusb.c b/tmk_core/protocol/vusb/vusb.c
index 2a29fe65d9..fdbfcc17dc 100644
--- a/tmk_core/protocol/vusb/vusb.c
+++ b/tmk_core/protocol/vusb/vusb.c
@@ -621,6 +621,23 @@ const PROGMEM uchar shared_hid_report[] = {
     0x81, 0x02, //     Input (Data, Variable, Absolute)
 #    endif
 
+#    ifdef JOYSTICK_HAS_HAT
+    // Hat Switch (4 bits)
+    0x09, 0x39,       //     Usage (Hat Switch)
+    0x15, 0x00,       //     Logical Minimum (0)
+    0x25, 0x07,       //     Logical Maximum (7)
+    0x35, 0x00,       //     Physical Minimum (0)
+    0x46, 0x3B, 0x01, //     Physical Maximum (315)
+    0x65, 0x14,       //     Unit (Degree, English Rotation)
+    0x95, 0x01,       //     Report Count (1)
+    0x75, 0x04,       //     Report Size (4)
+    0x81, 0x42,       //     Input (Data, Variable, Absolute, Null State)
+    // Padding (4 bits)
+    0x95, 0x04, //     Report Count (4)
+    0x75, 0x01, //     Report Size (1)
+    0x81, 0x01, //     Input (Constant)
+#    endif
+
 #    if JOYSTICK_BUTTON_COUNT > 0
     0x05, 0x09,                  //     Usage Page (Button)
     0x19, 0x01,                  //     Usage Minimum (Button 1)